Craftcloud offers a wide range of materials, including plastics, metals, and a variety of finishes and colors for each.
305 results
Nylon PA12 is one of the most widely used SLS materials. It is a tough, versatile plastic with low moisture absorption and good chemical resistance for durable functional parts.
PETG offers good impact resistance and strong layer adhesion, plus reliable chemical and moisture resistance. It is a good choice for everyday functional parts.
316L Stainless Steel is a highly durable alloy known for its corrosion resistance and versatility in both industrial and aesthetic applications.
AlSi10Mg is a lightweight cast-type aluminum alloy with high as-built strength and good thermal and electrical conductivity, suited to functional metal parts, with strength and ductility depending on heat treatment.
ABS is a durable, impact-resistant plastic with good heat tolerance, and is well suited to functional parts and prototypes that need to handle everyday stress.
Developed by HP, MJF Nylon is a widely used material for strong and detailed end-use parts and prototypes.
Tough resin is an impact-modified photopolymer that trades some of standard resin's stiffness for significantly better elongation and impact resistance. This makes it better suited to functional parts that need to withstand stress without cracking.
The strongest 3D printable material, titanium offers good dimensional accuracy and fine details.
PLA+ and Tough PLA offer enhanced strength and durability compared to regular PLA, which makes them ideal for functional prototypes and mechanical parts.
Aluminum Alloy 6061 offers excellent strength-to-weight performance, good corrosion resistance, and reliable dimensional stability. It is ideal for lightweight structural parts, prototypes, and functional components requiring durability and machinability.
17-4 PH Stainless Steel is a martensitic precipitation-hardening steel with very high strength and hardness after heat treatment and corrosion resistance similar to 304, though it is magnetic and less corrosion resistant than 316.
Polycarbonate (PC) is an engineering-grade plastic with the highest heat resistance and impact strength of common FDM materials, and it is ideal for demanding functional parts and prototypes.
MJF glass-filled nylon PA12 is a stiff PA12 with the same properties in every direction and higher heat deflection under load than standard nylon. It is a good choice for rigid functional parts.
Carbon fiber PETG is a reinforced composite that adds significant stiffness and dimensional stability to standard PETG, trading some impact resistance for rigidity. It is ideal for parts that need to hold their shape under load.
Maraging steel is a class of ultra-low-carbon, ultra-high-strength steels hardened by aging, reaching roughly 1,400–2,400 MPa depending on grade, suited to tooling inserts, molds, and high-strength parts.
SLS flexible TPU is a rubber-like, tear-resistant material with very good shock absorption and abrasion resistance. It's suitable for flexible functional prototypes and wear-prone parts.
Carbon fiber PPA is a high-performance composite that pushes heat resistance and dimensional stability well beyond standard carbon fiber nylon. It is suited to demanding engineering applications exposed to elevated temperatures.
Carbon fiber nylon is a reinforced composite that significantly increases stiffness and heat resistance over standard nylon, trading away some of nylon's signature impact resistance and flexibility in the process.
Elastic resin (Shore 50A–65A) is a soft, rubber-like photopolymer with high elongation and good rebound, ideal for prototyping silicone-like parts that need to stretch, compress, and flex repeatedly.
High-detail 316L Stainless Steel is 316L built with finer layers, which allows for thinner walls (about 0.5 mm) and smaller features than standard 316L, with similar strength and high ductility.
Nylon-like resin is an impact-modified photopolymer formulated to mimic nylon's flexibility and toughness, offering meaningfully better durability than standard resin. However, it doesn't fully match the toughness of actual printed nylon.
Flexible resin (Shore 80A) is a soft-touch, rubber-like photopolymer similar in firmness to a shoe heel. It combines flexibility with more rigidity and detail retention than elastic resin.
FDM nylon is a tough, wear-resistant engineering plastic known for high impact resistance, low friction, and the ability to flex repeatedly without cracking, all of which make it ideal for functional, moving parts.
Carbon Fiber PLA is a reinforced composite that significantly increases stiffness and dimensional stability over standard PLA, though this comes at the cost of increased brittleness.
PCTG is a tougher, clearer alternative to PETG. It offers notably better impact resistance and moisture resistance while it retains PETG's ease of use and chemical resistance.
Inconel 718 is a precipitation-hardening nickel-chromium superalloy with high strength, creep resistance, and fatigue strength at temperatures up to about 700 °C.
HP® 3D HR PA 12 S delivers exceptional surface quality and precision right out of the printer. The material is perfect for functional prototypes and high-end consumer goods.
PC-ABS is a polymer blend that combines polycarbonate's heat resistance and toughness with ABS's easier processability and dimensional stability, striking a middle ground between the two.
Glass fiber nylon (PA-GF) adds stiffness, heat resistance, and dimensional stability to nylon at a lower cost than carbon fiber nylon, while retaining significantly better impact resistance and toughness.
Accura® ClearVue is a clear, transparent resin with low moisture absorption that simulates the appearance of polycarbonate and ABS, suited to lens and headlamp models, fluid-flow visualization, and transparent assemblies.
Multi Jet Fusion PA11, produced by HP, is a bio-derived powder with exceptionally high toughness. This material offers high ductility and impact strength for all applications, especially functional parts.
Somos® Taurus is a tough, charcoal-colored resin with thermoplastic-like performance and better heat resistance than most standard resins (heat deflection about 62–91°C), suited to demanding functional prototypes and end-use parts.
Elastic silicone rubber (AR-G1) is a silicone-like rubber offered in a softer grade (AR-G1L, Shore A35) and a firmer grade (AR-G1H, Shore A65), suited to flexible design models and soft prototypes.
Carbon fiber polycarbonate (PC-CF) adds significant stiffness, heat resistance, and dimensional stability to standard PC.
Nylon PA11 is a bio-based nylon, made from castor oil, with high ductility and impact resistance. It is suitable for durable functional parts that need to flex or absorb impact.
High-temperature resin offers a notably higher heat deflection temperature than standard resin. This makes it a strong choice for heat-resistant mounts, fixtures, and housings that need to hold their shape under sustained heat.
Recycled rPETG reprocesses post-consumer or post-industrial PETG waste into new filament. It offers a sustainable alternative to virgin PETG with comparable strength, toughness, and chemical resistance.
Somos® EvoLVe 128 is a tough, white resin that looks and feels like a finished plastic, suited to functional prototypes, snap-fits, and fixtures, though it softens at about 50 °C.
Flame retardant polycarbonate (PC-FR) combines polycarbonate's strength and heat resistance with a UL94 V-0 fire rating. This makes it a strong choice for electrical enclosures and components near heat sources.
FDM PEEK is a premium engineering thermoplastic that combines exceptional heat resistance, strength, and chemical resistance with genuine biocompatibility. It is used where metal replacement or medical-grade performance is required.
Silicone resin produces soft, flexible parts with rubber-like elasticity and durability. It offers moderate rebound, fine detail resolution, and reliable performance for seals, gaskets, and functional flexible prototypes.
SLS polypropylene is a lightweight, ductile, chemically resistant plastic that tolerates repeated bending. It is suited to durable functional parts, though it softens at around 60 °C under load.
PETG-ESD is a PETG modified with carbon nanotubes so static charge drains away gradually, suited to electronics enclosures, jigs, and fixtures.
Bronze (90% copper, 10% tin) is a harder, more tarnish-resistant alternative to brass with a warm reddish tone, suited to antique-style jewelry, miniatures, and decorative parts.
BioMed resin is a biocompatible photopolymer certified under ISO 10993 for medical device applications, with specific contact type and duration varying by exact formulation.
Accura® Xtreme is a tough resin with good elongation that simulates polypropylene and ABS for snap-fits, assemblies, and functional prototypes, though it deflects under load at only about 54–62 °C.
SLS food safe nylon PA12 is a durable, chemical-resistant nylon made from a powder grade certified for food contact, suited to tools and components used in food processing.
Rigid resin is a glass-reinforced photopolymer that offers a high level of detail, stiffness, and deformation resistance.
ABS-ESD is an ABS modified with a conductive additive so static charge drains away gradually, suited to electronics enclosures, jigs, and fixtures, though it is less ductile and impact-resistant than standard ABS.
Flame retardant PETG is a halogen-free PETG designed to self-extinguish (to UL 94 V-0 criteria), suited to electronics enclosures and machine parts, though weaker than regular PETG and with a heat deflection of only about 60 °C.
GreenTEC Pro Carbon is a biopolymer made from renewable resources combined with 10% carbon fiber. The material offers high rigidity, very good mechanical properties and an increased temperature resistance.
Metal binder jetted 316L Stainless Steel is sintered to 96–99% density with ductility like conventional 316L, but its yield strength is well below laser-melted 316L.
Polypropylene is a versatile and durable material, highly suitable for compliant and functional parts. The FDM technology provides a cheaper alternative to SLS or MJF printed parts.
ULTEM 1010 offer the highest tensile strength and the highest chemical and thermal resistance of any FDM thermoplastic.
SLS glass-filled nylon PA12 is a stiff, wear-resistant PA12 with higher heat deflection under load than standard nylon, suited to rigid functional parts, though it is less ductile.
Accura® 25 is a white, polypropylene-like resin (Shore 80D) with good elongation and shape retention, used to simulate and replace CNC-machined polypropylene parts such as snap-fits and functional assemblies.
Carbon fiber ABS is ABS reinforced with chopped carbon fiber (typically 10–15%), giving much higher stiffness and slightly better heat resistance than standard ABS, though it is less ductile.
Durable resin is a polypropylene-like photopolymer with low modulus, high elongation, and the highest impact strength of common resin options. It is ideal for pliable parts like living hinges and low-friction moving components.
GreenTec Pro is a high performance biodegradable material made from 100% natural resources. With a high heat resistance (up to 160 °C) and mechanical stress resistance, the material is ideal for demanding applications.
Figure 4® HI TEMP 300-AMB is a rigid, translucent amber resin with a heat deflection temperature above 300 °C even under higher load, suited to testing high-temperature parts, molds, and flow visualization, though it is brittle.
Flame retardant resin is a photopolymer that self-extinguishes rather than sustaining flame, which makes it a strong choice for electronics and industrial parts near heat or ignition sources.
Somos® GP Plus 14122 is ideal for functional prototypes, concept models, and low volume production parts.
MJF flexible TPU is a rubber-like, tear-resistant material with high rebound and good abrasion resistance that's suited to flexible functional prototypes and wear-prone parts.
PETG-HT is an enhanced version of PETG, specifically designed to withstand high temperatures and exhibit excellent mechanical properties.
ULTEM 9085 is a high-performance thermoplastic with excellent chemical resistance and an extreme level of flame retardancy.
Carbon-reinforced PEEK is stiffer and somewhat stronger than normal PEEK, with a much higher heat deflection temperature under load, though it is far less ductile.
Nylon PA6 is a stiff, heat-resistant nylon that is stronger than PA12 when dry. It is sutiable for rigid functional parts, though it absorbs more moisture and is less flexible.
Markforged® Onyx is a nylon filled with chopped micro carbon fiber, about 1.4 times stronger and stiffer than ABS, with a heat deflection of 145 °C at light load, suited to functional prototypes and end-use parts.
Elastomeric polyurethane (EPU) is a rubber-like polyurethane (Shore 68A) with good elastic recovery, tear resistance, and energy damping, suited to gaskets, seals, vibration isolation, and impact absorption.
Ceramic resin is a high-resolution photopolymer that produces rigid parts with excellent stiffness, heat resistance, and dimensional accuracy.
Somos® PerFORM is a white, ceramic-filled composite resin that is very stiff and heat resistant (up to about 268 °C), suited to tooling, wind tunnel models, and high-temperature testing, though it is brittle.
SLS PEEK is a high-performance thermoplastic that offers high tensile strength, good heat resistance, and broad chemical resistance in a lightweight part, if with low ductility.
PVB filament is a semi-rigid material that can be smoothed to a glossy, layer-free finish, with low warping, suited to display models and visual prototypes
Conductive PLA is a carbon-filled PLA that conducts electricity well enough for low-voltage, low-current parts such as touch sensors and simple circuits, with a volume resistivity of about 30 Ω·cm along the layers.
PA 2200 is a widely used white nylon 12 grade with a balanced profile of strength, stiffness, and chemical resistance. It is a standard for functional SLS prototypes and rugged, end-use industrial components.
PHA (Polyhydroxyalkanoate) filament is a biodegradable type of plastic used in 3D printing, made through the fermentation of plant sugars by bacteria. It a great choice for applications that require biodegradability.
SLS PA6 carbon fiber is a stiff, dimensionally stable nylon composite with higher heat resistance than unfilled PA6. It is suitable for rigid structural parts, though it has low ductility.
SLS nylon PA12 carbon fiber is a 23% carbon-fiber-filled nylon 12, suited to rigid parts and tooling.
PPSU is a heat- and chemical-resistant material suited for automotive, aerospace, and plumbing applications.
MJF polypropylene is a lightweight, chemically resistant plastic with consistent properties in every direction. It is suited to durable functional parts and fluid-handling components, though it softens at around 60 °C under load.
Multicolor FDM prints using ASA combine vibrant color separation with exceptional UV, heat, and weather resistance. Ideal for outdoor signage, automotive parts, and durable prototypes needing both strength and visual impact.
PP-like resin is a flexible, impact-resistant photopolymer designed to simulate polypropylene. It offers high elongation, good durability, and strong resistance to cracking, making it ideal for living hinges, clips, and functional prototypes.
Glass fiber PEEK is PEEK reinforced with glass fiber for better creep resistance, stiffness, and dimensional stability under sustained load at high temperature, with PEEK’s broad chemical resistance, though it is less suited to wear applications.
Flame-retardant PA 12 for MJF, offering durability, dimensional stability, and fire compliance for functional and safety-critical parts.
Formlabs's surgical guide resin is a CE certified, biocompatible material that meets Class I requirements.
Castable wax resin blends real wax into a photopolymer base, combining standard resin printer compatibility with burnout behavior closer to pure wax than standard castable resin achieves.
SLS PA11 carbon fiber is a stiff, lightweight nylon composite with much higher stiffness and heat resistance under load than standard PA11. It is best used for rigid parts, though with less ductility.
A great material for striking visual models.
PA12 CCF is a is a co-extruded material consisting of nylon PA12 with a composite of nylon and continuous carbon fibers. This unique combination gives the finished part a smooth surface along with high strength, toughness, and durability.
Nylon PA66 is a strong, stiff nylon with good chemical resistance and heat tolerance, well above PA12 in strength and stiffness, though it absorbs far more moisture.
SLS glass-filled nylon PA6 is a very stiff nylon composite with high heat deflection (about 200 °C under load). It's a good choice for rigid, heat-exposed functional parts, though the material is not flexible and still absorbs moisture.
Figure 4® RUBBER-BLK 10 is a hard rubber-like black resin (Shore 59D/97A) with high tear strength and slow rebound, suited to grips, handles, bumpers, strain relief, and overmolds, though it is much firmer than soft rubber.
Alumide is an aluminum-filled nylon 12 with a metallic gray look, high stiffness, and heat deflection around 144 °C under load, suited to rigid parts, jigs, and models, though it is less flexible than standard nylon.
Glass-filled polypropylene is a tough material with high strength that is also resistant to high temperatures. It is suitable for functional verification of product prototypes.
Glass fiber ULTEM 1010 is ULTEM 1010 polyetherimide reinforced with glass fiber for added stiffness and dimensional stability, built on a resin with a glass transition of about 215 °C.
PET 3D prints offer a strong balance of toughness, chemical resistance, and dimensional stability. The material produces durable parts with good layer adhesion and a semi-gloss surface finish.
Recycled rABS reprocesses post-consumer or post-industrial ABS waste into new filament. It offers a sustainable alternative to virgin ABS with mechanical properties that hold up well through recycling.
SLS PK is a tough, ductile polyketone with excellent chemical and fuel resistance, very low moisture absorption, and low friction and wear, suited to functional parts exposed to fluids, though it is somewhat less stiff than PA12.
Carbon fiber PET is a PET filament reinforced with chopped carbon fiber, offering high stiffness, low moisture absorption, and higher heat deflection than PETG, though it is brittle and weaker across the layers.
VisiJet® M2R-TN parts have a durable, tan-colored finish with excellent impact resistance and dimensional accuracy. Ideal for functional prototypes and mechanical components, they offer high performance straight from the printer.
VisiJet® Armor M2G-CL offers high strength, impact resistance, and precise dimensional accuracy. The material’s light gray color and durability make it ideal for functional prototypes and end-use parts that require high mechanical performance.
SLS PEKK-CF is a carbon-fiber-reinforced PEKK that is very stiff and holds its shape under load up to roughly 200 °C. It is a good option for rigid high-temperature parts, though it is brittle and weaker across the layers.
HP® 3D HR PA 12 W is a high-reusability, white nylon (polyamide 12) designed for durable, functional 3D printed parts with excellent chemical and mechanical resistance.
PEKK filament is a high-performance thermoplastic from the PAEK family, known for excellent thermal and chemical resistance, and mechanical strength. Ideal for aerospace, automotive, and high-tech industries, it excels in demanding environments.
LithaCon 3Y 210 is a zirconia stabilized with 3 mol% yttria, with about 99.4% relative density, a four-point bending strength of about 1,000 MPa, and high fracture toughness, abrasion resistance, and thermal shock resistance.
Carbon-reinforced ULTEM 9085 is a stiffer, stronger version of ULTEM 9085, though it is less ductile and weaker across the layers.
Titanium Grade 23 (ELI) offers exceptional biocompatibility, high strength-to-weight ratio, and excellent corrosion resistance.
Inkbit® Titan Tough Epoxy is a type of high-performance material known for its exceptional strength, durability, and resistance to harsh environmental conditions.
Food safe 316L Stainless Steel is a low-carbon austenitic stainless steel with excellent corrosion resistance and higher yield strength than conventionally made 316L, offered with food-contact documentation, suited to food-processing parts.
HP 3D HR TPA is a durable, flexible elastomer for MJF printing, perfect for functional parts like gaskets, seals, and wearables that require repeated bending or impact resistance.
Carbon-reinforced PEKK is a stiffer version of PEKK with modestly higher strength, though it is less ductile and weaker across the layers.
Nickel-titanium (NiTi, nitinol) is a shape memory alloy that recovers its shape after deformation, with superelastic recovery of about 3–6% strain in printed parts, though its behavior depends on precise nickel content and heat treatment.
ithaLox HP 500 is a high-purity (99.99%) alumina ceramic with 99.4% relative density, a four-point bending strength of 430 MPa, and a smooth surface.
PMMA is a porous acrylic material with low strength, used mainly for investment casting patterns and visual models.
Multicolor FDM prints using PETG combine vivid color separation with the material's toughness, flexibility, and chemical resistance. It is ideal for functional enclosures and durable prototypes that need both visual impact and everyday resilience.
As-printed multicolor FDM ABS has a ribbed, layered texture. Color regions are generally clean-edged, with minor bleed at color-change points. ABS has a matte look, unlike glossier PETG, and responds well to acetone vapor smoothing.
A soft, flexible polyurethane with Shore A 30 hardness, Inkbit® TEPU 30 delivers smooth, durable, and highly detailed parts ideal for gaskets, seals, and cushioning components.
LithaBone TCP 300 is a beta-tricalcium phosphate (β-TCP) ceramic at 98% relative density that the body resorbs and replaces with new bone, suited to bone substitute implants and scaffolds with defined pore geometries.
Food safe aluminum (AlSi10Mg) is a lightweight alloy with good thermal conductivity and high as-built strength, supplied with a food-contact coating, suited to food-processing parts that avoid acidic or salty foods.
Food safe titanium (Ti-6Al-4V) is a lightweight, non-magnetic, corrosion-resistant alloy with high strength, offered with food-contact documentation, suited to food-processing parts that need strength at moderate temperatures.
High-detail 17-4 PH Stainless Steel is 17-4 PH built with finer layers, which allows for thinner walls and smaller features than the standard grade.
SLS flexible TPE is a rubber-like elastomer, available from very soft to firm, that withstands repeated bending and vibration, suited to gaskets, dampers, and soft functional parts, though it is weak and softens at modest temperatures.
High-detail bronze (90% copper, 10% tin) is a harder, more tarnish-resistant alternative to brass with a warm reddish tone, suited to jewelry and miniatures with very small sections.
iglidur® I190-PF is a material that offers high-strength and wear-resistance for low-friction, dry-running parts. It is deal for bushings, gliding elements, and motion components in automation and machinery.
Flame retardant SLS nylon PA12 is PA12 formulated to self-extinguish, with fire ratings such as UL 94 V-0 that depend on wall thickness, suited to electrical and transport components, though it is less ductile than standard PA12.
Markforged® copper is a 99.8% pure copper with 84% IACS electrical conductivity and 350 W/m·K thermal conductivity. It is soft and ductile, and is suited to heat sinks, bus bars, and induction coils.
Markforged® Inconel 625 is a nickel-chromium superalloy with high corrosion resistance and strength at high temperatures, suited to high-temperature fixtures and corrosion-resistant fittings.
PVC filament is renowned for its exceptional durability and resistance to moisture. Its versatility and robustness make it a favored option for creating functional prototypes, outdoor signage, and parts that require water-resistant properties.
Aluminum 6061 is a strong, lightweight alloy with excellent corrosion resistance and good machinability. Ideal for aerospace, automotive, and general-purpose CNC-milled parts.
Aluminum 7075 is a high-strength, heat-treatable alloy with excellent strength-to-weight ratio and fatigue resistance. Ideal for aerospace, motorsports, and high-load structural components.
Stainless Steel 304 is strong, corrosion-resistant, and ideal for precise CNC-milled parts in automotive, aerospace, and industrial use. It offers excellent durability and dimensional stability.
Carbon Steel C45 is a medium-carbon, non-alloy steel with moderate strength, higher than that of lower-carbon grades. It is commonly used for shafts, axles, spindles, studs and general engineering components.
Acetal (POM-C) is a high-performance copolymer known for its excellent machinability, dimensional stability, and low friction. Ideal for precision parts like gears and bearings, it offers high strength and moisture resistance.
Carbon Steel 1018 is a versatile, low-carbon steel known for its machinability, weldability, and strength, and is suitable for gears, shafts, and structural parts.
Stainless Steel 17-4 PH is a strong, corrosion-resistant alloy ideal for high-stress parts. It’s used in aerospace, medical, and tooling applications, and can be heat-treated for added hardness.
Aluminum 6082 is a high-strength, corrosion-resistant alloy used in structural and aerospace applications. It offers good weldability, dimensional stability, and strength-to-weight ratio.
Brass C360 is a highly machinable alloy with excellent corrosion resistance, ideal for precision parts like connectors, fittings, and gears in automotive, electrical, and industrial applications.
Stainless Steel 303 is a corrosion-resistant, machinable alloy used for high-precision components such as gears, shafts, and fasteners in automotive, aerospace, and industrial applications.
Brass H59 is a 60/40 copper-zinc brass with high strength and hardness, good hot-forming behavior, and fair machinability. It is a lower-cost choice for hardware, fittings, and general mechanical parts.
Tool Steel A2 (annealed) is a machinable, tough, and dimensionally stable steel, ideal for CNC parts, fixtures, dies, and precision tools, with the option for later hardening.
CNC Copper 101, also known as Oxygen-Free Electronic (OFE) copper, is a high-purity alloy with 99.99% copper content, providing excellent electrical and thermal conductivity.
Carbon Steel A36 is a low-cost, structural steel with good strength and weldability. Ideal for frames, brackets, and general-purpose parts. It offers low corrosion resistance and moderate machinability.
Delrin® (POM-H) is a high-strength acetal homopolymer known for superior stiffness, hardness, and creep resistance. It is the go-to material for high-load mechanical parts like heavy-duty gears, bearings, and precision fasteners.
Polycarbonate (PC) is a tough, transparent thermoplastic ideal for impact-resistant parts like lenses, covers, and housings in automotive, electronics, and protective applications.
PEEK is a high-strength, heat-resistant thermoplastic with exceptional chemical resistance, wear resistance, and dimensional stability. Ideal for high-performance components in aerospace, automotive, and medical industries.
Nylon PA6 is a durable, wear-resistant thermoplastic with excellent impact strength, low friction, and good machinability. Ideal for precision mechanical components like gears, bushings, and automotive parts.
CNC machined Aluminum 2024 produces high-strength, lightweight parts with excellent dimensional accuracy and a clean machined surface. It is well suited for structural and performance components where strength-to-weight ratio matters most.
CNC-milled ABS is strong, impact-resistant, and ideal for prototypes and housings. It machines well, has a matte finish, and is widely used in engineering, electronics, and product design.
CNC-milled acrylic offers high clarity, smooth edges, and a glass-like finish. Ideal for displays, covers, and enclosures, it’s precise, weather-resistant, and suited for low-impact uses.
Sheet metal forming shapes metal sheets using techniques like bending and stamping. It's used in automotive, aerospace, and electronics for precise, durable parts.
4J50 is a nickel-iron precision alloy with thermal expansion matched for soft-glass and ceramic sealing, plus soft-magnetic characteristics.
Tool steel S7 ships annealed for easy machining and is hardened afterward into a shock-resisting tool steel built for impact toughness rather than maximum hardness, suited to tools and dies under repeated impact.
Laser cutting is a precise manufacturing process that uses a high-powered laser beam to melt, burn, or vaporize material, creating clean and accurate cuts in various metal types.
Grade 23 Ti-6Al-4V is a high-purity medical titanium alloy. It offers low density, extreme biocompatibility, high fracture toughness, and corrosion resistance. It is ideal for medical implants, aerospace, and high-stress functional parts.
Brass C260 produces strong, corrosion-resistant parts with excellent formability and an attractive gold-colored finish. It is ideal for precision components, decorative hardware, and electrical applications.
PEEK GF30 produces extremely strong, stiff, and heat-resistant parts with excellent dimensional stability and chemical resistance, ideal for high-performance structural applications.
Carbon Steel 1215 produces highly precise parts with excellent machinability and a smooth surface finish. It offers moderate strength and is ideal for high-volume production of detailed components where tight tolerances and cost efficiency are priorities.
Tool Steel P20 produces strong, wear-resistant parts with excellent toughness and dimensional stability. It is ideal for molds, tooling, and precision components requiring reliable mechanical performance.
Tool steel 6F7 (1.2767) is a high-nickel alloy tool steel valued for exceptional toughness even at high hardness, which makes it a strong choice for applications needing impact resistance alongside wear resistance.
Aluminum 6063 is a medium-strength, heat-treatable alloy with excellent corrosion resistance and good formability. It's ideal for precision parts in architectural, structural, and electronic applications.
Zinc alloy produces strong, corrosion-resistant parts with excellent machinability and dimensional stability. It is ideal for precision components, hardware, and mechanical applications requiring durability and fine detail.
Copper CuCr1Zr is a high-performance copper alloy with superior thermal/electrical conductivity, strength, and high-temperature softening resistance. Ideal for welding electrodes, heat sinks, and rocket components.
Stainless Steel 15-5 produces strong, corrosion-resistant parts with excellent dimensional accuracy and a clean machined surface. It is well suited for high-strength structural and industrial components.
Vacuum casting is a manufacturing process used to create detailed and precise prototypes or small production runs of plastic and rubber parts.
Nickel Alloy 2.4858 (Alloy 825) is a titanium-stabilized nickel-iron-chromium alloy with excellent resistance to sulfuric and phosphoric acids, chloride stress corrosion cracking, and weld-related intergranular corrosion.
Nickel Alloy 2.4889 (Alloy 45TM) is a nickel-chromium-iron-silicon alloy designed for high-temperature oxidizing, carburizing, and sulfur-bearing atmospheres, resisting scaling up to about 1,000 °C.
Nickel-Iron Alloy 2.4610 (Alloy C-4) is a nickel-molybdenum-chromium alloy with high pitting resistance and very good resistance to hydrochloric acid. It stays ductile and corrosion resistant after prolonged heating and welding.
Nickel Alloy 2.4816 (Alloy 600) is a nickel-chromium-iron alloy that resists chlorides, oxidation, and hot alkalis, keeping good properties from low to elevated temperatures.
Nickel Alloy 2.4602 (Alloy 22) is a nickel-chromium-molybdenum-tungsten alloy with outstanding resistance to pitting, crevice corrosion, and both oxidizing and reducing acids.
Nickel Alloy 2.4605 (Alloy 59) is a nickel-chromium-molybdenum alloy with very low carbon and silicon that offers outstanding resistance to chloride pitting and mixed acids and good thermal stability.
Nickel Alloy 2.4851 (Alloy 601) is a nickel-chromium-iron alloy with added aluminum for outstanding oxidation resistance up to about 1,200 °C and good resistance to carburizing conditions.
Nickel Alloy 2.4600 (Alloy B-3) is a nickel-molybdenum alloy with outstanding resistance to hydrochloric acid at all concentrations.
MoldJet® 316L Stainless Steel is a 316L from a sinter-based process that reaches about 99.9% relative density, with near-isotropic tensile strength and high ductility, suited to corrosion-resistant parts.
Nickel Alloy 2.4633 (Alloy 602 CA) is a high-carbon nickel-chromium-iron-aluminum alloy with outstanding creep strength and oxidation resistance at temperatures up to about 1,200 °C.
Nickel Alloy 2.4360 (Alloy 400) is a nickel-copper alloy with exceptional resistance to seawater and hydrofluoric acid, offering moderate strength and toughness for marine and chemical equipment.
Cobalt-Iron Alloy 1J22 (Permendur) is a soft magnetic alloy with the highest saturation induction of any common soft magnetic material, and is used for lightweight, high-performance motors, transformers, and electromagnets.
Zinc Alloy Zamak 5 adds about 1% copper to Zamak 3 for roughly 10% more strength and higher hardness, with reduced ductility, a good fit where more tensile performance is needed.
LithaBone HA 400 is a hydroxyapatite ceramic (85% relative density, 15% porosity) that is absorbed more slowly than tricalcium phosphate, giving the body more time to heal, made from HA powder certified to ASTM F1185-03.
Markforged® H13 is a hot-work tool steel that is suited to tool bodies, brazing fixtures, and mold inserts, though about 94.5% dense and less ductile than wrought H13.
Ultrafuse 316L produces sintered 316L stainless steel parts with high ductility and corrosion resistance, similar in strength to annealed wrought 316L, though with lower yield strength than laser-melted 316L.
Figure 4® High Temp 150 °C FR Black is a rigid, halogen-free, flame-retardant black resin rated UL 94 V-0 at 2 and 3 mm, with a heat deflection of 150 °C under light load, suited to electrical housings and transport parts, though brittle.
BASF® Ultracur3D® RG 3280 is a ceramic-filled resin designed for functional 3D printing. It offers high stiffness, excellent heat resistance, and a smooth white finish, which makes it ideal for durable prototypes and demanding end-use parts.
Ultracur3D® EL 60 is a flexible, clear resin with excellent elasticity, tear resistance, and durability. It combines rubber-like performance with high accuracy, making it suitable for functional prototypes and industrial parts.
SLS PA11 ESD is a bio-based, castor-oil nylon with much lower surface resistance than standard PA11. It dissipates static charge from tools, jigs, and housings used around sensitive electronics.
Zinc Alloy Zamak 8 (ZA-8) is a higher-aluminum zinc alloy with high strength, hardness, and creep resistance. It is well suited to decorative parts and components under sustained load.
Zinc Alloy Zamak 3 is the most widely used Zamak grade, offering a balanced mix of strength, ductility, and impact resistance, with better dimensional stability than higher-copper Zamak 2.
ULTEM 2300 produces high-strength, heat-resistant parts with excellent stiffness, dimensional stability, and flame resistance. It is ideal for structural and high-performance engineering applications.
PEI ULTEM 1000 is a high-strength, heat-resistant thermoplastic ideal for aerospace, automotive, and industrial applications. It offers excellent flame resistance, mechanical properties, and dimensional stability.
Nickel-Iron Alloy 1J85 (Supermalloy) is a soft magnetic alloy with about 80% nickel and 5% molybdenum. It offers very high permeability and low coercivity for weak-field shielding, sensors, and transformers.
Nickel-Iron Alloy 1J79 (Moly Permalloy) is a soft magnetic alloy with about 80% nickel and 4% molybdenum. It offers extremely high permeability for weak-field applications, such as magnetic shielding and sensitive sensors.
Nickel-Iron Alloy 1J50 (FeNi50) is a soft magnetic nickel-iron alloy (about 50% nickel) that combines high magnetic permeability with high saturation induction. It is used for transformer cores, relays, and magnetic circuit parts.
Iron-Chromium Alloy 1J117 is a corrosion-resistant soft magnetic alloy, the equivalent of 430FR solenoid-quality stainless. It offers moderate magnetic performance for solenoid valves and electromagnetic parts.
Copper C182 (chromium copper) combines high electrical conductivity with good strength retention at elevated temperatures. This makes it a strong choice for resistance welding equipment and high-current electrical components.
Copper C180 is a beryllium-free alternative to the nickel-beryllium copper family. It offers strong mechanical properties and moderate conductivity.
Copper C17510 (nickel-beryllium copper) trades some of C17200's extreme strength for substantially better electrical conductivity. This makes it the better choice when both performance and conductivity matter more than peak strength alone.
Copper C172 (beryllium copper) is the strongest copper alloy commercially available, reaching tensile strength comparable to steel while retaining useful electrical conductivity, though machining requires strict beryllium dust controls.
Aluminum 5086 is a non-heat-treatable aluminum-magnesium alloy with excellent seawater corrosion resistance and good weldability, and is widely used for marine hulls but limited to cooler service temperatures.
Aluminum 5454 is a non-heat-treatable aluminum-magnesium alloy with very good corrosion resistance and moderate strength, and it is chosen over higher-magnesium marine alloys for tanks and vessels that run warm.
Copper C150 is a zirconium copper alloy that retains nearly all of pure copper's exceptional electrical conductivity while offering improved strength and resistance to softening at elevated temperatures.
Rigid polyurethane is a stiff polyurethane resin comparable to ABS, suited to consumer, automotive, and industrial parts.
E-Mould is a strong, high detail material, which can be used to print molds used for injection molding of various plastics.
PA12 CBF is a co-extruded material consisting of nylon PA12 with a composite of nylon and continuous basalt fibers. This unique combination gives the finished part a smooth surface along with strength, toughness, and durability.
PETG CCF is a clear PETG shell with a PETG and continuous carbon fiber composite inside. This unique combination results in a part with a much higher tensile strength than PETG alone with a smooth translucent finish.
VisiJet® M2S-HT90 is a strong and rigid material for applications requiring temperature resistance and/or rigidity, ideal for rapid tooling, under the hood parts, enclosures and housings
Ultrafuse 17-4 PH produces sintered 17-4 PH stainless steel parts that are strong, magnetic, and corrosion resistant, and can be heat treated to higher strength, though with lower ductility than other metal 3D printing processes.
Copper C102 is oxygen-free copper (99.95% minimum) with the same high conductivity as standard copper. It is chosen where purity matters, such as vacuum use and brazed or welded assemblies.
Carbon Steel C45E is a medium-carbon steel with a specified low sulfur limit. It offers higher strength and hardness than low-carbon mild steel, with good machinability and the option of heat treatment.
Stainless mold steel 420 ships annealed and machinable, and can then be hardened into a corrosion-resistant plastic mold steel, combining genuine stainless properties with good polishability.
Zamak 2 is the strongest, hardest, and most wear-resistant grade in the Zamak family, thanks to its high copper content, although this comes at the cost of lower ductility than other Zamak grades.
Tool steel O2 ships annealed and machinable, then oil-hardens into a general-purpose cold-work tool steel similar to O1 but with added manganese for improved hardenability.
Stainless steel 302 is a higher-carbon variant of 304; it offers slightly greater strength and hardness – especially after cold working – while retaining 304's same corrosion resistance.
Stainless steel 304L is a low-carbon variant of 304, engineered to resist sensitization during welding at a slight cost to strength. This makes it the preferred choice for welded assemblies and processing equipment.
Nickel Silver C77000 is a copper-nickel-zinc alloy with a white, silver-like appearance. Despite its name, it contains no silver. It is tarnish resistant and has better corrosion resistance than standard brass.
Stainless steel 316 is arguably the classic marine-grade stainless, adding molybdenum over 304 for superior resistance to chlorides and reducing acids.
Tool steel M42 ships annealed for machining and is hardened afterward into a cobalt-enhanced high-speed steel reaching higher hardness than standard M2, suited to the most demanding cutting applications despite being more brittle and costly.
Tool steel H13 ships annealed and machinable, and can then be air-hardened into a chromium-molybdenum hot-work tool steel valued for strength at elevated temperature, good toughness, and resistance to heat-cracking and thermal fatigue.
Tool steel D3 ships annealed and machinable, and can then be hardened into a high-carbon, high-chromium cold-work steel with excellent wear resistance.
Tool steel D2 ships annealed and machinable, and can then be hardened into one of the most widely used cold-work tool steels, prized for exceptional wear resistance, high compressive strength, and excellent dimensional stability.
Tool steel M2 ships in a soft, machinable annealed state and can be hardened and tempered afterward to become the industry-standard high-speed steel, balancing wear resistance, toughness, and red-hardness.
Tool Steel D6 ships annealed and machinable, and can then be hardened into a high-chromium cold-work steel with added tungsten for better through-hardening.
Tool Steel W1 ships annealed and highly machinable, and is the simplest and most economical tool steel, water-hardened afterward for applications without demanding heat or wear requirements.
Tool steel S1 ships annealed and machinable, and can be hardened into a shock-resisting tool steel combining tungsten's toughness and wear resistance with chromium's dimensional stability.
Polypropylene (PP) is a lightweight, durable thermoplastic ideal for CNC machined parts that require chemical resistance, low friction, and fatigue resistance. It is often used in automotive, medical, and consumer applications.
CNC-machined steel S355J2 is a higher-strength European structural steel, offering roughly 50% greater yield strength than S235JR, with guaranteed toughness down to -20 °C for demanding structural and cold-environment applications.
CNC-machined steel S235JR is the most widely used European non-alloy structural steel, valued for excellent weldability, formability, and machinability at a low cost, though with only moderate strength.
Brass C377 is a leaded brass optimized for hot forging and finish machining, offering good strength and excellent hot formability. It is the workhorse grade for valve bodies and fittings.
CNC-machined Aluminum 6026 offers free-machining performance similar to Aluminum 2011 but with better corrosion resistance, developed specifically to meet modern automotive and electronics environmental compliance directives.
Aluminum AW-2011 is the reference-standard free-machining aluminum alloy, though it has poor corrosion resistance and almost no weldability.
Copper C145, also known as tellurium copper, is copper with a small tellurium addition. It offers high electrical and thermal conductivity with mechanical properties similar to pure copper, and is a common choice for machined copper parts.
Brass C485, also known as high-leaded naval brass, is a tin-bearing brass with added lead. The tin gives it seawater corrosion resistance comparable to Brass C464, while the lead makes it a common choice for machined parts.
Brass C464, also known as naval brass, is a copper-zinc alloy with a small tin addition. The tin improves its corrosion resistance in seawater, including against dezincification, which can affect plain 60/40 brass.
Aluminum 5005 is a non-heat-treatable aluminum-magnesium alloy best known for producing an exceptionally consistent anodized finish, though it machines less readily than 3003 or 6061.
Aluminum 3003 is a non-heat-treatable, manganese-strengthened alloy prized for excellent corrosion resistance and formability, though it offers lower strength than heat-treatable grades like 6061.
Aluminum 1100 is a commercially pure (99% min) aluminum grade offering the best corrosion resistance and electrical/thermal conductivity of the wrought aluminum family, at the cost of lower strength than alloyed grades.
Super-Invar (4J32) is an iron-nickel-cobalt precision alloy with the lowest thermal expansion of the Invar family, ideal for ultra-precision dimensional stability.
Pure Iron DT4 is an electromagnetic-grade pure iron prized for high magnetic permeability and low coercivity in DC electromagnetic components.
Nickel 200 (Pure Nickel N6) is a commercially pure nickel grade that offers excellent alkali corrosion resistance and high electrical and thermal conductivity.
Magnesium AZ91D is the most widely used die-cast magnesium alloy, and it offers the best corrosion resistance in the AZ family alongside good strength-to-weight performance.
Magnesium Alloy AZ31B is a lightweight, highly machinable wrought alloy that offers good ductility and vibration damping, though it needs surface protection in humid or corrosive environments.
Kovar (4J29) is a nickel-cobalt-iron alloy engineered to match the thermal expansion of hard borosilicate glass and alumina ceramics for reliable, crack-free hermetic seals.
Invar 36 (4J36) is the classic 36% nickel-iron alloy famous for its extremely low thermal expansion up to about 200 °C.
Alloy 42 (4J42) is a 42% nickel-iron alloy engineered to match the thermal expansion of hard glass and ceramics for hermetic electronic sealing.
Acetal (glass-filled) is a reinforced engineering thermoplastic enhanced with glass fibers. This addition significantly increases the material's stiffness, creep resistance, and dimensional stability compared to standard acetal.
Titanium Grade 7 is a corrosion-resistant, commercially pure titanium-palladium alloy that offers the best chemical resistance of any titanium grade, especially against reducing acids and chlorides.
Super Duplex Stainless Steel 2507 offers the highest corrosion resistance and strength in the duplex family, as it's built for extreme chloride exposure like offshore and desalination equipment.
Duplex Stainless Steel 2205 combines roughly double the yield strength of standard austenitic grades with excellent resistance to chloride pitting, crevice corrosion, and stress corrosion cracking.
Stainless steel 202 is a low-nickel, manganese-strengthened austenitic alloy that performs similarly to 304 in mild, indoor environments at a lower material cost.
Stainless steel 444 is a molybdenum-added ferritic alloy with corrosion resistance approaching 316L, and it's essentially immune to chloride stress corrosion cracking.
Stainless steel 430 is a magnetic, chromium-only ferritic alloy offering a bright, polishable finish at lower cost than nickel-bearing grades.
Stainless Steel 201 is a cost-effective, manganese-strengthened austenitic alloy that offers good strength and formability.
Stainless steel 321 is a titanium-stabilized austenitic alloy that is engineered to resist intergranular corrosion during welding and sustained high-temperature service.
Stainless steel 309S is a high-chromium, high-nickel austenitic alloy built for sustained oxidation resistance at elevated temperatures, well beyond standard stainless steel 304 or 316L.
Stainless Steel 409 is a low-cost, titanium-stabilized ferritic alloy built for heat and exhaust-gas resistance, not for decorative or highly corrosive applications.
Stainless steel 310S is a high-chromium, high-nickel austenitic alloy that offers the strongest oxidation resistance of this group, suited to continuous service near 1,100 °C.
Stainless steel 301 is an austenitic alloy prized for its high work-hardening rate, and it offers greater achievable strength than 304 at the cost of lower corrosion resistance.
Laser cutting is a precise manufacturing process that uses a high-powered laser beam to melt, burn, or vaporize material, creating clean and accurate cuts in various wood types.
Steel 4340 produces extremely strong, tough parts with excellent fatigue and wear resistance. This nickel-chromium-molybdenum alloy steel is ideal for high-performance and heavily loaded mechanical components.
Titanium Grade 2 produces lightweight, corrosion-resistant parts with excellent strength and durability. It is ideal for precision components exposed to harsh environments and demanding applications.
Alloy Steel 4140 (Pre-Hardened) produces high-strength, pre-hardened parts with excellent wear resistance, toughness, and dimensional stability. It is ideal for demanding mechanical components that require durability without additional heat treatment.
Alloy Steel 4130 (1.7218) produces strong, tough parts with excellent fatigue resistance and good weldability. This chromium-molybdenum alloy steel is ideal for structural and high-performance components requiring durability and reliability.
Delrin® AF is a unique thermoplastic composite of PTFE fibers uniformly dispersed in Delrin acetal resin. It combines the high strength of POM-H with the exceptional self-lubricating properties of PTFE for ultimate low-friction performance.
Stainless steel 440C produces extremely hard, wear-resistant parts with excellent strength and moderate corrosion resistance. It is ideal for precision components requiring high durability and long service life.
Stainless steel 416 produces precise parts with excellent machinability, good strength, and moderate corrosion resistance. It is ideal for high-volume production of detailed components requiring tight tolerances and clean surface finishes.
Stainless steel 410 produces strong, wear-resistant parts with good machinability and moderate corrosion resistance. It is well suited for structural and mechanical components requiring hardness and durability.
PVC produces lightweight, corrosion-resistant parts with excellent chemical resistance, electrical insulation, and reliable dimensional stability for industrial and technical applications.
Nylon 6/6 produces strong, wear-resistant parts with excellent toughness, low friction, and good chemical resistance. It is ideal for durable mechanical components and precision applications.
Stainless Steel 18-8 produces corrosion-resistant, durable parts with good strength and a clean machined surface. It is widely used for general-purpose components requiring reliability in humid or mildly corrosive environments.
Stainless Steel 420 produces high-strength, hardened parts with excellent wear resistance and moderate corrosion resistance. It is ideal for components requiring durability, sharp edges, and long service life.
Tool steel O1 produces high-strength, wear-resistant parts with excellent hardness potential and dimensional stability. It is ideal for precision tooling and durable mechanical components.
Aluminum 2017A is a high-strength, heat-treatable alloy with excellent machinability, ideal for aerospace, automotive, and precision components requiring a strong, lightweight material.
Commercially pure iron offers excellent machinability, magnetic properties, and ductility. It is ideal for magnetic, scientific, or precision parts requiring minimal alloy content.
Alloy Steel 4140 produces high-strength, wear-resistant parts with excellent toughness and fatigue resistance. This alloy steel is ideal for demanding mechanical and structural applications requiring durability and precision.
CNC machined Aluminum MIC-6 produces dimensionally stable, flat, and precise parts with a clean machined surface. It is ideal for tooling plates, fixtures, and structural components where accuracy and stability are critical.
SLS glass-filled polypropylene is a stiffer, stronger polypropylene that resists heat much better under load (around 130 °C) than unfilled PP, with good chemical resistance, although it is denser and less ductile.
Scalmalloy® is a high-strength aluminum-magnesium-scandium alloy, suited to lightweight brackets, thermal management components, and ducts.
Solid oak is a strong, hard, heavy hardwood with a bold, visible grain, suited to CNC-machined furniture parts, signage, and decorative pieces.
Aluminum 5083 is a corrosion-resistant, high-strength alloy ideal for CNC machined parts in marine, automotive, and aerospace applications.
Injection molding involves injecting molten plastic into a mold, where it cools and solidifies into a precise shape. Ideal for high-volume production, it ensures consistent quality, detailed designs, and material flexibility across various industries.
Laser cutting is a precise manufacturing process that uses a high-powered laser beam to melt, burn, or vaporize plastics, producing clean edges and accurate cuts across a variety of materials.
Copper C110 produces highly conductive, corrosion-resistant parts with excellent thermal and electrical performance. It is ideal for electrical, thermal, and precision components requiring reliable conductivity.
Bronze C932 produces durable, wear-resistant parts with excellent machinability and good corrosion resistance. It is ideal for bushings, bearings, and components requiring low friction and long service life.
CNC-machined Aluminum 7050 produces very high-strength, lightweight parts with excellent dimensional accuracy and a clean machined surface. It is suited for demanding structural and aerospace applications where maximum performance is required.
Sheet metal joining connects metal sheets using welding, riveting, adhesives, or fasteners, essential for creating durable assemblies across industries.
UHMW-PE is a highly durable thermoplastic with exceptional wear resistance, low friction, and chemical resistance, ideal for high-performance parts in machinery, food processing, and industrial applications.
Nickel-Iron Alloy 1J36 is a soft magnetic alloy with about 36% nickel, specified for magnetic performance and resistance to humid or salt-spray environments rather than for low thermal expansion.
CNC-machined Copper C122 (DHP copper) is a phosphorus-deoxidized copper that welds and brazes well and resists hydrogen embrittlement, with lower conductivity than C110.
CNC-machined Copper Nickel C706 (90/10) is a copper-nickel alloy with excellent seawater corrosion resistance and good resistance to biofouling, a lower-cost choice for marine piping and valve parts.
CNC-machined Copper Nickel C715 (70/30) is a high-strength copper-nickel alloy with excellent seawater corrosion and erosion resistance, suited to faster-flowing and more demanding marine service than 90/10.
CNC-machined Brass C274 (yellow brass) is a 63/37 copper-zinc brass with good ductility, excellent cold workability, and moderate machinability, suited to plumbing fittings, electrical connectors, and drawn parts.
Brass C210 (gilding metal) is a copper-rich brass (about 95% copper, 5% zinc) with high electrical and thermal conductivity and good ductility, suited to jewelry components, craft metalwork, and decorative hardware.
Brass C230 (red brass) is an 85/15 copper-zinc brass with excellent corrosion resistance, excellent cold workability, and excellent brazing and soldering. It is suited to plumbing fittings, hardware, and fasteners.
Brass C280 (Muntz metal) is a 60/40 copper-zinc brass with higher strength than 70/30 brasses and excellent hot-forming behavior, suited to hot-forged parts, condenser plates, and large fasteners.
CNC-machined Carbon Steel 1010 is a very low-carbon steel with good ductility and formability, low strength, and fairly good machinability. It is suited to cold-headed fasteners and low-stress parts.
CNC-machined Carbon Steel 1015 is a low-carbon steel (about 0.15% carbon) with good ductility and slightly more strength than 1010, suited to light-duty machine parts and formed components.
CNC-machined Carbon Steel 1020 is a commonly used low-carbon steel with a good balance of strength and ductility, good machinability, and the ability to be hardened or carburized. It is suited to general machine parts.
CNC-machined Carbon Steel 1025 is a low-carbon steel (about 0.25% carbon) with slightly more strength than 1020 and good ductility and machinability, suited to general machine parts.
CNC-machined Carbon Steel 1035 is a medium-carbon steel with higher strength and hardness than the low-carbon grades, good machinability, and the ability to be heat treated. It is suited to shafts and stressed machine parts.
CNC-machined Carbon Steel 1040 is a medium-carbon steel that can be heat treated to high strength, with good ductility.
CNC-machined Alloy Steel 12Cr1MoV is a low-alloy chromium-molybdenum-vanadium heat-resistant steel with good creep strength and weldability.
CNC-machined Alloy Steel 30CrMnSiA is a chromium-manganese-silicon steel that reaches at least 1,080 MPa tensile strength after quenching and tempering, with good toughness, suited to high-strength structural parts.
Alloy Steel 40Cr is a medium-carbon chromium steel with much better hardenability than plain 45 steel, reaching at least 980 MPa tensile strength after quenching and tempering, suited to shafts and gears.
Carbon Steel 65Mn is a high-carbon manganese spring steel with good elasticity and hardenability, reaching at least 980 MPa tensile strength after quenching and tempering.
Tool Steel 75Cr1 (annealed) is a high-carbon chromium steel (0.70–0.80% carbon) that hardens to about 44–52 HRC for saw blades and knives, though it has no corrosion resistance.
Tool Steel 9SiCr (annealed) is a low-alloy cold-work steel with high hardenability that hardens to at least 62 HRC, suited to taps, reamers, and dies, though toughness is limited.
Tool Steel Cr12MoV (annealed) is a high-carbon, 12% chromium cold-work steel with very high wear resistance, suited to dies and molds, though it has low toughness.